MVP210-MVP210 - FXO to FXS Auto Call Setup
(This example only covers the parameters you must change to get this working.  Leave any parameters I don't mention at their default values)

Local MVP210 Connected to PBX Extensions/Station Ports

Configuration -> Ethernet / IP

	IP Parameters

1. Configure IP Address, IP Mask, and Gateway addresses (a Gateway address will not       be required if both MVP210's are on the same private IP subnet).

2.   Click OK on the Ethernet / IP page to save these changes.

Configuration -> Interface

1.  Configure Interface Type as FXO for both channels.

2. Click OK on the Interface page to save this change.


Configuration -> Voice/Fax

1. Enable MultiVOIP to Auto Call the Remote MVP210 as follows:

a) Channel 1 - Configure Auto Call / OffHook Alert to Auto Call and enter 201 as 
Phone Number.
b) Channel 2 - Configure Auto Call / OffHook Alert to Auto Call and enter 202 as 
Phone Number.

2. Click OK on Voice/Fax page to save these changes.

Phone Book -> Phone Book Modify -> Outbound Phone Book

Create the following Outbound Phone Book entry:

#1  Destination Pattern = 201				
      Remove Prefix = Blank 
      Add Prefix = Blank 
      IP Address = IP Address of Remote MVP210
      Description = Whatever you want (or leave blank)
      Protocol Type = H.323 (use SPP protocol if voips are MVP-FX models) 
      
#2  Destination Pattern = 202				
      Remove Prefix = Blank 
      Add Prefix = Blank 
      IP Address = IP Address of Remote MVP210 
      Description = Whatever you want (or leave blank)
      Protocol Type = H.323 (use SPP protocol if voips are MVP-FX models) 
      



	Phone Book -> Phone Book Modify -> Inbound Phone Book

Create the following Inbound Phone Book entry:

#1  Remove Prefix = 101 
      Add Prefix = Blank  
      Channel Number = Channel 1 
      Description = Whatever you want 
      Call Forward = Not enabled 

#2  Remove Prefix = 102 
      Add Prefix = Blank  
      Channel Number = Channel 2 
      Description = Whatever you want 
      Call Forward = Not enabled



	Save Configuration

1.  Click Save Setup -> Save and Reboot to save these configuration changes to the MultiVOIP.



Remote MVP210 Connected to Analog Telephone/PBX Line port

Configuration -> Ethernet / IP

	IP Parameters

1. Configure IP Address, IP Mask, and Gateway addresses (a Gateway address will not       be required if both MVP210's are on the same private IP subnet).

2.   Click OK on the Ethernet / IP page to save these changes.

Configuration -> Interface

1.  Configure Interface Type as FXS (Loop Start) for both channels.

2. Click OK on the Interface page to save these changes.


Configuration -> Voice/Fax

2.  Enable Remote MVP210 to Auto Call the MVP210 connected to the PBX as follows:

a) Channel 1 - Configure Auto Call / OffHook Alert to Auto Call and enter 101 as 
Phone Number.
b) Channel 2 - Configure Auto Call / OffHook Alert to Auto Call and enter 102 as 
Phone Number.

1. Click OK on Voice/Fax page to save these changes.


Phone Book -> Phone Book Modify -> Outbound Phone Book

Create the following Outbound Phone Book entry:

#1  Destination Pattern = 101				
      Remove Prefix = Blank 
      Add Prefix = Blank 
      IP Address = IP Address of MVP210 at other location
      Description = Whatever you want (or leave blank)
      Protocol Type = H.323 (use SPP protocol if voips are MVP-FX models)
      
#2  Destination Pattern = 102				
      Remove Prefix = Blank 
      Add Prefix = Blank 
      IP Address = IP Address of MVP210 at other location
      Description = Whatever you want (or leave blank)
      Protocol Type = H.323 (use SPP protocol if voips are MVP-FX models)


	Phone Book -> Phone Book Modify -> Inbound Phone Book

Create the following Inbound Phone Book entry:

#1  Remove Prefix = 201 
      Add Prefix = Blank  
      Channel Number = Channel 1 
      Description = Whatever you want 
      Call Forward = Not enabled 

#2  Remove Prefix = 202 
      Add Prefix = Blank  
      Channel Number = Channel 2 
      Description = Whatever you want 
      Call Forward = Not enabled


Save Configuration

1.  Click Save Setup -> Save and Reboot to save these configuration changes to the MultiVOIP.